Yes you need a case.I see that...
https://www.aiyima.com/products/amp...switching-power-supply?variant=32961903394891
Would I need a case for it?
See: https://www.audiosciencereview.com/...255-review-amplifier.18984/page-7#post-623356
Yes you need a case.I see that...
https://www.aiyima.com/products/amp...switching-power-supply?variant=32961903394891
Would I need a case for it?
So,
48V 7.3A with 4R load, we get 213.16 watts being lowest ?
48V 7.3A with 8R load, we get 288 watts being lowest ?
48V 3A with 4R load, we get 36 watts being lowest ?
48V 3A with 8R load, we get 72 watts being lowest ?
32V 5A with 4R load, we get 100 watts being lowest ?
32V 5A with 8R load, we get 128 watts being lowest ?
24V 10A with 4R load, we get 144 watts being lowest ?
24V 10A with 8R load, we get 72 watts being lowest ?
Mine sits level, no issue there however volume knob issues have been commented on in this forum. Your issue doesn't sound the same as mine; I had a issue where the knob rubbed at points so I used a couple of washers on the pot stem as a spacer behind the knob which resolved the issue.Does anyone's A07 not sit level on their desk? Meaning it wobbles if you press one or more corners? I know that this is a dirt cheap amplifier and I shouldn't expect perfection, but I'm wondering if I should exchange it. My volume knob is also not a consistent friction. If I turn it just the right way I can make it squeak.
Mine sits level but squeaks too.Does anyone's A07 not sit level on their desk? Meaning it wobbles if you press one or more corners? I know that this is a dirt cheap amplifier and I shouldn't expect perfection, but I'm wondering if I should exchange it. My volume knob is also not a consistent friction. If I turn it just the right way I can make it squeak.
Does anyone's A07 not sit level on their desk? Meaning it wobbles if you press one or more corners? I know that this is a dirt cheap amplifier and I shouldn't expect perfection, but I'm wondering if I should exchange it. My volume knob is also not a consistent friction. If I turn it just the right way I can make it squeak.
look mismatched next to each other
While not perfect the A07 would sit better on top of a Topping D30, or D10s. Not that this helps you a this point.
Small stands are available, for example S1 Multi layer Acrylic Audio Rack Mount Stand for HiFi Desktop Amplifier/Preamp/DAC|Amplifier| - AliExpress
So I just got my T5. Is anyone else a little annoyed that the dimensions don't line up? The T5 is too wide to put on top of the A07, and it's also a different height so they look mismatched next to each other. I was hoping for a matched stack like Schitt does.
I just checked the dimensions for the A5 Pro and yes they match the A07. But one has to ask themselves what is more important; how the stack looks or how the system sounds. While I can vouch for the A07 and Topping D30 performance ( I own both) I can't comment on any of the Aiyima DAC's and Amir hasn't had the opportunity to test one yet (I actually asked him earlier this week).But isn't A07 supposed to go together with AIYIMA DAC A5 Pro, not T5? A-series goes with A-series, you know.
I just checked the dimensions for the A5 Pro and yes they match the A07. But one has to ask themselves what is more important; how the stack looks or how the system sounds. While I can vouch for the A07 and Topping D30 performance ( I own both) I can't comment on any of the Aiyima DAC's and Amir hasn't had the opportunity to test one yet (I actually asked him earlier this week).
Makes sense to me. Just one caution the E30 is only 12.5 cm deep and the A07 feet are 12.5 cm centre to centre.Well the whole reason I went with the T5 was to have an analog input for my turntable.... but now I think I might return the T5 and get the Topping E30 (I like the screen) and an ADC for the (very cheap Crosley C100A) turntable. That price of that shelf is also a factor... I'd rather just spend that on proven hardware. Yes sound is important but looks matter too